Tiltex 10mm thick 40Mpa Concrete Geotextile, 5m wide x 20m roll
10mm thickness, 40Mpa Concrete. 5 m wide x 20 m roll. Install as a Geotextile / Concrete powder / Geotextile system. The Tiltex system from GEOmasta is a composite 40mpa concrete geotextile that is supplied on a roll. This is laid out on site, hydrated and left to dry, providing a simple and effective lining for V drains, embankments, channels and spillways or as an alternative to shotcrete.
Product Description
The Tiltex system from GEOmasta is a composite 40mpa concrete geotextile that is supplied on a roll. This is laid out on site, hydrated and left to dry, providing a simple and effective lining for V drains, embankments, channels and spillways or as an alternative to shotcrete.
Tiltex is a needle punched composite, consisting of concrete-sand mix, embedded and fixed between two layers of geo-textile. It is much faster and cheaper to install than conventional materials, and our strict quality control of raw materials makes the finished product fail-proof. It provides a substrate for direct applications of a thin protective layer of regular concrete, which may be used in various weather conditions. The fabric is fastened to an outer part with nails, which provides a solid water-resistant surface stabilisation, further braced thanks to internal reinforcing fibers.
An additional advantage of the Tiltex System is that there is no need for special installation equipment. It is much faster and cheaper than conventional materials used in the lining of ditches, reservoirs, slopes banks and trenches.
Applications:
- "V" Drains
- Embankment Lining
- Spoon Drains
- Erosion Control
- Weed Suppression
- Road Applications including Drains, Replacing Shotcrete, Erosion Control
- Channel Lining & Pits Lining
- Alternative & Cost Effective solution to Shotcreting
- Enhancing existing concrete structures in order to avoid degradation
- Embankment Lining
- Bund Lining
- Slope Stabilization
- Alternative to Grout & Revetment Mattress
- Spillways
- Trenches/Swale Drains Lining
- Underground Wire Protection
Product Variants Available
| Properties of Tiltex (1) | Tiltex 07 | Tiltex 09 | Tiltex 10 | Tiltex 12 |
| Mass per unit area of concrete EN 14196 | 7000 g/m2 (±10%) | 9000 g/m2 (±10%) | 10000 g/m2 (±10%) | 12000 g/m2 (±10%) |
| Mass per unit area of Tiltex EN 14196 | 7550 g/m2 (±10%) | 9550 g/m2 (±10%) | 10550 g/m2 (±10%) | 12550 g/m2 (±10%) |
| Thickness EN ISO 9863 -1/-2 | 7,0 mm (±1mm) | 9,0 mm (±1mm) | 10,0 mm (±1mm) | 12,0 mm (±1mm) |
Specifications
| Index Properties | Test Method | Values |
| Carrier Layer - PP Nonwoven Composite | - | 350 g/m2 |
| Cover Layer - PP Nonwoven | - | 200 g/m2 |
| Chemical composition | XRF | Sand-cement mix |
| Density | Typical | 3,0 g/cm3 |
| Bulk Density | Typical | 1,1 g/cm3 |
| Setting Start | PN-EN 196-3 | > 90 min |
| Properties of Tiltex (1) | | |
| Tensile Strength MD | EN ISO 10319 | = 20,0 kN/m (±10%) |
| Tensile Strength CMD | EN ISO 10319 | = 20,0 kN/m (±10%) |
| CBR Puncture Strength | EN ISO 12236 | = 3,0 kN/m (±10%) |
| Properties of Tiltex (2) | | |
| Compressive Strength MD | ASTM C 109-02 | 40 MPa |
| Bending tests based | PN EN 12467:2013-03 | 6,0 MPa |
| Standard Roll Dimensions | Test Method | Value |
| Width x Length | Typical | (5,0 x 20) m / (2,5 x 20) m |
| Quantity | Typical | 100 m2 / 50 m2 |
(1) Before hydration (2) After hydration
These data are average values derived from standard tests and are subject to usual product variation. The right is reserved to make changes without notice at any time.
*Specifications as per manufacturer.
.png)